Close

10A DC 12V - 24V PWM Solar charge controller with LCD and 5V USB

AL130-10A

New

18 Products in stock in our warehouse.

€ 9,88

 tax 0% incl.

Data sheet

Target platform Solar charge controller
Amperage 10A
Voltage 24V
Characteristics With USB port
Color characteristics Blue
Warranty 2 years

More info

This controller is a intelligent, multi-purpose solar charge and discharge controller. Fixed LCD display with a very friendly interface is used in this product; various control parameters can be flexibly set, fully meet your various application requirements. 
  
PRODUCT FEATURES           

1.Build-in industrial micro controller.

2.Big LCD display,all adjustable parameter.

3.Fully 4-stage PWM charge management.

4.Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection.

5.Dual mosfet Reverse current protection ,low heat production.
              

SYSTEM CONNECTION 

1.Connect the battery to the charge regulator - plus and minus. 
2.Connect the photovoltaic module to the regulator - plus and minus. 
3. Connect the consumer to the charge regulator - plus and minus. 
The reverse order applies when deinstalling! 
An improper sequence order can damage the controller!
 
SPECIFICATON:
MODEL  CY1210 CY1220 CY1230
Battery Voltage  12V 24V Auto 
Charging Current  10A  20A  30A 
Discharging Current  10A  20A  30A 
Max Solar input  50V(for 24V battery) 25V(for 12V battery) 
Equalization  14.4V(Sealed) 14.2V(Gel) 14.6V(Flood)
Float charge  13.7V(default,adjustable)
Discharge stop  10.7V(defaultadjustable)
Discharge reconnect  12.6V(default,adjustable)
USB output  5V/3A 
Self-consume  <10mA 
Operating temperature 

 

-35°C~+60°C 

 

*all red color voltage X2 ,while using 24V system.

SAFETY Manual

Full consideration to the safety of persons and property has been given when designing the products.

However, the incorrect connection may cause the system breakdown or even safety accident. For your safety and benefits, the following rules must be complied during the operation.

 Installation of this product shall be tinder the guidance of the professionals in this field.

Prevent this controller from water, humidity and insects, to avoid short-circuit.

Keep children and incapable persons away from the controller

Keep the controller away from electrical heater, heating machine and other high temperature electrical

appliances; avoid the controller suffering from insulation directly.

Please check the rated voltage of solar panel, battery, and loads before connection. 12V rated voltage is 12V, 24V rated voltage is 24V.

Make sure connections between positive and negative poles of Solar panels, Battery and Loads are correct.

The diameter of connecting cable must be matched with the requirements of the current. Do not use thinner diameter cable, the thinner diameter. The larger resistance, this will cause higher temperature and output power

The total rated current of solar panel and loads must be smaller than the rated current of the controller.

Components of system must be correctly and firmly connected. Prevent the terminals from oxidation and moldy, to avoid connection trouble.

 

Warning:

Before connecting to the solar panel, please connect the controller to the battery; do not use solar panel supply power

to the loads directly.

Notes:

Do not use lamplight to charge the solar panel (lamplight is too weak to charge)

DC power source to replace the solar panel will cause troubles to controller.

Choose the suitable wire which diameter should not be too small, please refer to the parameter.

 

INDICATE LIGHT AND BUTTON.

When Red LED (CHARGE) is on, battery is charged up strongly; When Red LED is flickering, battery is MPPT charged up in constant voltage; when Red LED is oft charge off

When Green LED (LOAD) is on, loads are working; when Green LED (LOAD) is off, loads stop working.

Three Color changing LED (BATTERY), When light is red, it indicates low voltage, green indicate battery full charged, orange indicate normal status.

 

TROUBLE SOLUTION

Phenomenon: Green LED off, battery indicator LED is red.

Reason: Low voltage of battery

Solution:

A: Cut off the power, disconnect the load; reconnect the load after the charge become normal.

B: Battery charge problem: Increase the solar panel power or change the battery.

Phenomenon: Battery indicator LED is orange and Load indicator LED is green, the loads cannot work.

Reason: Over load or short-circuit causes the controller inner fuse cut off

Solution: 10-20 minutes after eliminated the malfunction, the fuse will automatically back to working.

Also Bought Products

30 other products in the same category

Close