Victron MultiPlus 24V/3000VA/70A-50/120V VE.Bus Inverter Charger PMP243021102

Attention! : this is a 120V model.

The Victron MultiPlus 24/3000/70 inverter/charger combination is a powerful sine wave inverter, an advanced battery charger with adaptive charging technology and a fast AC changeover switch in a single compact housing. Due to the steel/aluminium housing (protection class IP21), these MultiPlus models are easy to recognize.

Victron MultiPlus 24/3000/70 inverter/charger specifications:
Input voltage: 120VAC and 24VDC | Output voltage: 120VAC
Output power: 3000VA / 2400W | Peak: 6000W
AC Inputs: 1 | AC outputs: 2
PowerControl: yes | PowerAssist: yes | Transfer switch: 50A
Charging current house battery: 70A | Charging current starter battery: 4A
Maximum forward current: 50A
Recommended battery capacity: 350 - 700 Ah
Recommended DC fuse: 300A - See "Order directly"
Battery connection: Four M8 bolts (2 positive and 2 negative connections)
Battery cable (not included): 50mm² or 2x 25mm² - See "Order directly"
NB! : the diameter (mm²) of the battery cables is based on a maximum length of 5 meters.
The MultiPlus 24/3000/70 combines a powerful 3000 VA (2400 Watt) pure sine wave inverter, an advanced battery charger with 70 amp adaptive charging technology, and a super fast AC changeover switch in a single compact metal housing. This MultiPlus is supplied without the required 50mm² or 2x 25mm² cables and has four (4) M8 bolts (2 positive and 2 negative connections) for the battery connection.

All MultiPlus models from this series are equipped with PowerControl and PowerAssist functionality. All models are also suitable for three-phase and parallel connection. This model has a maximum forward current of 50A. Victron Energy's inverter/chargers are designed for professional use. They are suitable for a variety of devices with high and low starting powers. The MultiPlus is a multifunctional energy system with a sine wave inverter, battery charger and AC transfer switch. The batteries are safely charged, even if the quality of the power supply is low.

Proven reliability
The full bridge plus toroidal transformer topology has proven itself very reliable for many years. The inverter is short-circuit proof and protects against overheating, whether due to overload or high ambient temperature.

PowerControl - Maximum utilization of limited aggregate, shore or grid power
A maximum aggregate or shore power can be set with the Digital Multi Control control panel. The MultiPlus then takes other power consumers into account and only uses the power that is 'left' for charging, so that the generator or shore connection is not overloaded.

PowerAssist – Do more with your generator or shore power
Where peak power is often only needed for a short time, the MultiPlus ensures that insufficient shore or aggregate power is immediately supplemented with power from the battery. When the load decreases, the reserve current is used to recharge the battery.

High start-up power
Required to start loads with high inrush current, such as voltage converters for LED lamps, halogen lamps or power tools.

Automatic and uninterrupted switching (UPS function)
In the event of a power failure or if the power supply from the shore or a generator is interrupted, the inverter in the Multi is automatically activated to provide power to the connected loads. This happens so quickly (in less than 20 milliseconds) that computers and other electronic devices can continue to function undisturbed.

Two AC outputs (the second output is only available on models 3 kVA and above)
The main output has uninterrupted functionality. The second auxiliary output switches off when no external AC source is available, and thus becomes active only when AC voltage is available on the AC input of the MultiPlus. Heavy loads that should not discharge the battery, such as a boiler, can be connected to this output.

Virtually unlimited power thanks to parallel connection
Up to six Multis can be connected in parallel to provide greater power. Power supply via three-phase current or single-phase current is also possible. On the datasheets you can see which models do and do not have these options.

Three-phase switching
In addition to the parallel connection, three units of the same model can be configured for three-phase output. But that's not all: up to 6 sets of three units can be paralleled for an inverter power of 75 kW / 90 kVA and a charging capacity of more than 2000A.

Search Mode
When the 'search mode' is enabled, the inverter power consumption at no load is reduced by approx. 70%. The 'search mode' means that the Multi is switched off when there is no load or when it is very low. Every 2 seconds the Multi will switch on briefly. If the output current exceeds a set level, the inverter continues to operate. If not, the inverter switches off again.

AES (Automatic Economy Switch)
Instead of 'search mode', the AES mode can also be selected. When this setting is enabled, the power consumption at no load and low load is reduced by approx. 20% by 'narrowing' the sine wave. The AES mode is not adjustable with DIP switches and is only applicable in 'stand alone' configuration.

Programmable Relay
The programmable relay is set as alarm relay by default, ie the relay is de-energized in case of an alarm or a pre-alarm (inverter almost too hot, input ripple voltage almost too high, battery voltage almost too low).

Solar energy: alternating current always available - even during a mains failure
The MultiPlus can be used in both autonomous and grid-connected PV and other alternative energy systems. Software to detect power loss is available.

Local or remote monitoring and control - optional
Monitor and control your MultiPlus system locally (LAN) or remotely via the internet from around the world with the free VRM app and the free VRM portal website. Access is possible for multiple operating systems via a phone, tablet, laptop or PC. Multiple options are available: Battery Monitor (BMV), Multi-Control Panel, Color Control GX and other GX communication devices, VE.Bus Smart Dongle for smartphone or tablet (Bluetooth Smart) and with an interface cable for laptop or PC (USB or RS232 ). The level of control from customizing the MultiPlus to setting up a rental vehicle Geofence and more is endless. To get an impression of the VRM (Victron Remote Management) website, visit: Victron Remote Management and click on the 'Try Our Demo' button. Victron Remote Management (VRM) is a free service from Victron Energy for remote monitoring of electrical equipment around the world.

Local or remote configuration
- If in the case of a stand alone application the settings need to be changed, this can be done within a few minutes via a DIP switch setting procedure.
- Parallel and three-phase applications can be configured with VE.Bus Quick Configure and VE.Bus System Configurator software.
- Autonomous, grid-interactive and self-consumption applications, with inverters and/or MPPT solar chargers, can be configured with assistants (dedicated software for specific applications).
- When connected to the Ethernet, systems with a Color Control GX and other GX communication devices are accessible and settings can be changed.

Compact models 800VA - 5000VA
The MultiPlus C models are available in the power values ​​800VA, 1200VA, 1600VA, 3000VA in 12V and 24V voltage values, and the power values ​​3000VA, 5000VA in 48V.